I have been tying to get my unit reflashed/repaired but I cannot get the STV# up. Any Ideas as to how?
As I understand, once you have #STV up on the screen, you have access to the chip and you can start the repair process and reflash the various bits and pieces as per the previous posts. Anyway that is what I would/will do if I can get the #STV up.
Further, as I undersatnd it, the process and the subsequent updtaes will fix up your current error.
BTW could you post the way you have set up your wiring, ie Rx Tx & Pos Earth.
I note the Russian site uses a 3 wire system Rx Earth TX
Hello Enviro8
Sorry for my english (it is a translation by google)
Were you able to get to the line of STV #?
If yes, can you give me the procedure?
Any special TTL is no needed! Simple ttl cable on RS232 with TX, RX and GND.
For ATV1000 or ATV2000 you need only basic spi_M3_512.bin - that file we need form Geniatech support. But i think you can use spi from one spi update package.
Remember You do it at their own risk! I recommend that only to people with experiencewith linux or router developer.
I bought 2 of these ATV310 boxes and both of them have Wi-Fi issues. My ATV1000 never had this much trouble with Wi-Fi. Sometimes it would take a few tries to connect (it would take long at Obtaining IP Address) but never had speed issues. On the ATV310 I'm finally getting connected but only getting download speeds of 200-500Kbps (my internet is 10Mbps)!
Does anyone else have problems with the ATV310 (Nano) box and Wireless "N" routers? I expect the signal to be a little bit weaker because it does not have external antenna. But not this bad. Does it have the same wireless chipset as the ATV1000 or different?
I am using the Android 2.3 20120606 M1 firmware.
Thanks for your help.
Sounds like the same old problem on the ATV5xx series, Geniatech or the factory that makes them placed the wireless antenna in a really bad spot inside the case. You can take the ATV5xx case apart and re-position the antenna.
The ATV1xxx & higher series didn't suffer from this as they all used external antennas attached to the box.
The Following User Says Thank You to next121 For This Useful Post:
The Android Media Player AMP1000 from Diamond Multimedia is a rebranding of the Geniatech ATV1000. Most apps including XBMC are working fine.
But the screen size is too big, and important information is invisible at the screen edges.
I tried to use the Screen Position utility in the Settings menu, but it does not save my changes.
The help info says to press the "Back" key to save the settings. When I press the "ESC" key (which is the "Back" key on the remote), the settings are not saved.
Has anyone had this problem on their Enjoy TV?
Can anyone help me reduce the screen size on my AMP1000?
__________________
Jeff Schallenberg
Mont Saint Hilaire, Québec
--------------------------------------
Acer Iconia A100/ICS, Diamond Multimedia AMP1000/ICS
The Android Media Player AMP1000 from Diamond Multimedia is a rebranding of the Geniatech ATV1000. Most apps including XBMC are working fine.
But the screen size is too big, and important information is invisible at the screen edges.
I tried to use the Screen Position utility in the Settings menu, but it does not save my changes.
The help info says to press the "Back" key to save the settings. When I press the "ESC" key (which is the "Back" key on the remote), the settings are not saved.
Has anyone had this problem on their Enjoy TV?
Can anyone help me reduce the screen size on my AMP1000?
I have the same problem, but only on the "video player" screen when a movie is playing otherwise it is fine. I think this started when they updated their firmware so that you no longer need to reboot when you adjust the "Display Position" which was updated in the 20120606 firmware. Previous firmwares you needed to reboot after you adjust the Display Position which I guess does something extra to adjusts the display size of the "video player" screen.
After adjusting the Display Position and you press "back" button does it ask you to reboot or just asks you to confirm and press "OK"?
Hello. I have recently been having trouble with Google Play when trying to roll my own firmware using Gio's technique. Whenever I open any app in Google Play (just to see details of the app) it crashes. Here is the log from logcat.
Has anyone seen this before?
E/AndroidRuntime( 716): FATAL EXCEPTION: main
E/AndroidRuntime( 716): java.lang.NullPointerException
E/AndroidRuntime( 716): at com.google.android.finsky.utils.Nfc$GingerbreadMr1 NfcHandler.setPushMessage(Nfc.java:150)
E/AndroidRuntime( 716): at com.google.android.finsky.utils.Nfc$GingerbreadMr1 NfcHandler.onResume(Nfc.java:138)
E/AndroidRuntime( 716): at com.google.android.finsky.activities.DetailsDataBa sedFragment.onResume(DetailsDataBasedFragment.java :158)
E/AndroidRuntime( 716): at android.support.v4.app.FragmentManagerImpl.moveToS tate(FragmentManager.java:917)
E/AndroidRuntime( 716): at android.support.v4.app.FragmentManagerImpl.moveToS tate(FragmentManager.java:1080)
E/AndroidRuntime( 716): at android.support.v4.app.BackStackRecord.run(BackSta ckRecord.java:622)
E/AndroidRuntime( 716): at android.support.v4.app.FragmentManagerImpl.execPen dingActions(FragmentManager.java:1416)
E/AndroidRuntime( 716): at android.support.v4.app.FragmentManagerImpl$1.run(F ragmentManager.java:420)
E/AndroidRuntime( 716): at android.os.Handler.handleCallback(Handler.java:587 )
E/AndroidRuntime( 716): at android.os.Handler.dispatchMessage(Handler.java:92 )
E/AndroidRuntime( 716): at android.os.Looper.loop(Looper.java:130)
E/AndroidRuntime( 716): at android.app.ActivityThread.main(ActivityThread.jav a:3683)
E/AndroidRuntime( 716): at java.lang.reflect.Method.invokeNative(Native Method)
E/AndroidRuntime( 716): at java.lang.reflect.Method.invoke(Method.java:507)
E/AndroidRuntime( 716): at com.android.internal.os.ZygoteInit$MethodAndArgsCa ller.run(ZygoteInit.java:841)
E/AndroidRuntime( 716): at com.android.internal.os.ZygoteInit.main(ZygoteInit .java:599)
E/AndroidRuntime( 716): at dalvik.system.NativeStart.main(Native Method)
W/ActivityManager( 135): Force finishing activity com.android.vending/.AssetBrowserActivity
W/ActivityManager( 135): Activity pause timeout for HistoryRecord{40644338 com.android.vending/.AssetBrowserActivity}
If your market release is 3.4.4 or superior, you must remove this file: android.hardware.nfc.xml
from "permissions" folder in: /system/etc
Regarding my problem about Google Play crashing. ^^^ The post by Gio above is the fix. Make sure you remove the android.hardware.nfc.xml from the permissions folder. I was including it by mistake, I guess I was using an old copy of the full_permissions.zip.
So it seems I could try out the modded roms from this thread..
Has any one cracked the recovery option yet..
Be nice to be able to get a CWM or TWRP recovery going on it..
I know it can be done with uboot type devices as I can load it on a older flytouch tablet of mine..
If any of the the modded gurus here want to have a look at the file and see if it can be tweaked for these boxes..
_barsuk_CWMRecovery http://forum.xda-developers.com/showthread.php?t=1361956
I am not sure if the touch recoveries would work as I don't know if the touch can be replaced via keyboard or mouse commands..
Will try out the TWRP I got running on the transformer while plugged into the dock with usb mouse and see if it works..
If it does, and then this would mean it could be modified for this media boxes. As we could boot into via one of the boot to recovery apps.
Last edited by dgcruzing; September 22nd, 2012 at 11:04 AM.
So it seems I could try out the modded roms from this thread..
Has any one cracked the recovery option yet..
Be nice to be able to get a CWM or TWRP recovery going on it..
I know it can be done with uboot type devices as I can load it on a older flytouch tablet of mine..
If any of the the modded gurus here want to have a look at the file and see if it can be tweaked for these boxes..
_barsuk_CWMRecovery [ROM] (Flytouch 2, SuperPad, WWE10) 2.2 V2.5 #4325 - xda-developers
I am not sure if the touch recoveries would work as I don't know if the touch can be replaced via keyboard or mouse commands..
Will try out the TWRP I got running on the transformer while plugged into the dock with usb mouse and see if it works..
If it does, and then this would mean it could be modified for this media boxes. As we could boot into via one of the boot to recovery apps.
Hi,
It's actually my first post on this topic....
About CWM recovery, _fun from xda-developers did some successful work on that for M1 based media boxes... I personally don't have time or need right now to port cwm to m1/m3 platforms... _fun and others are developing CM9 to Amlogic platform with CWM included (it's mostly tablets but few builds for media boxes also exists). See this topic.
Hi wombat613, you can find "Professor Android" reinstalling previous SPI file
(that is previous uboot and recovery version).
This is the link: www.geniatech.com/down-eng/Androidtvbox/update_spi20111102.zip
Rename the file to update.img and install as usual (in recovery mode).
Well guys.. didnt take long for DG wreak havoc on his box..
now that he has identified he has the ATV3000 M1, and he had it running nicely on the Geniatech M1 Android 4.0 20120529, he thought he might try the moded..4.0 20120730 - Thanks gio965
Seemed to flash fine.. Bootup fine.. and pops in to launcher..
then oops becomes sticky as hell..
Launcher force closing, Market going painfully slow.. as was trying to download TB to load the backup..
Did a wipe of the box from within.. but still was sticky..
Did some tests.. pulled out my sdcard.. and it seemed to run fine.
Note: the card is a Microsd in the SDcover..so i was thinking this might be the problem.
Plugged in a freshly formatted 8g sdcard out of the camera..but started have FC's and sticking problems..
So maybe a bad flash..
Then preceded to flash Geniatech M1 Android 4.0 20120730 stock.. (off the fresh sdcard)
80% through the flash.. got a "Radom offset: 0xe9" error..
it sat on this but then booted.. had a play around and seemed to be soso..
a few FC and not as zippy as the original 20120529..
Note: I also lost the green professor during this process.. now onto the box and green man..
Anyway.. 12pm and had 6am wake up for work to time to turn it off..
Next night.. flashed back to 20120529..
Same problem..
80% through the flash.. got a "Radom offset: 0xe9" error.. eeeee..
anyway booted in to 529, and seemed to work sell enough for an hour or so that I played with it..
So once I was satisfied that I hadnt bricked it.. time to Flash 4.0 20120730-mod..
same problem.. 80% through the flash.. got a "Radom offset: 0xae" error.
Kinda know what this is.. as had it from the transformer.. the Rom is looking for a setup file.. cant find it and so wants to abort.. Anyway.. it flashed ok and boots ok.. problems I am getting are..
1: Market -even with fix (as per permissions file fix) it still doesn't want to load from market any file. not FC, just a DL error..
2: Random Launcher F/C
3: Just seems sticky over all after running for a while..
So.. reading through the thread I have found some fix's to try..
but this is where a good recovery would come in handy.. so we can do a good wipe before loading new Roms in..
Anyone got instructions on USB recoveries as yet..?
Once again.. as always.. thanks in advance to modder's and Rom developers..
and anyone else that helps out us Rom-flasheroholic's
edit: flashed.. update_fingerprint-tweak_and_market-resetter_for_ICS-0529.zip Geniatech Enjoy TV
no joy.. market not gimme me joy..
Flashed back to original 20120529.. its gimme some love now..
maybe my box just doesn't like the next version of upgrades.. at the moment.. on 529.. its back to zippy..
Like on the upgrade is like a slug on both stock rom and mod.. so for me its back to 529..
also as a note, I was able to boot into a recovery screen..using TB boot to recovery...
options are as follows..
1.reboot system
2.apply update
3.wipe date/factory reset
4.wipe cache partition
5.set efuse item ....(never seen this before anyone know what it means?)
to answer my own question..its got..just for factory testing..
a..audio licence
b...Ethernet Mac address
c...Bluetooth Mac
6. set output mode
Heading out of China back to Australia for mums 70th birthday tomorrow...so not going to get to play with it for a few weeks..
if you haven't tried out.. Ocean HD or My Beach HD.. do it.. they rock on this..
I had it setup with these and they look great.. get the girls over..rock some music off the streaming radio stations..(Ministry of Sound app for me..) and you are set for a night of .... as this is a family channel.. I leave it to your imagination..)
Last edited by dgcruzing; September 25th, 2012 at 09:11 AM.
I am going to need a new name..haha.. too many posts..
I wanna O/C this thing..
We need source for the kernel..
As I was saying above.. if we can get the 3 part flashing going.. then it means we can flash kernel separately..
i.e - flash u-boot upgrades..flash image upgrades and then flash Kernel..
Bloody Chinese need to release source so some bright bugger can work on it..
I am sure we could over clock the box's up to 1200-1400 as heat is not a problem on mine..
its got a fan and well ventilated.. so I would love to see how fast and stable the 800's are on o/c..
I am kinds spewing.. should have done a bit more research on them.. as the dual core are out already..
thinking of selling mine and upgrading already.. but might kill it instead with playing with it..as they are cheap enough..
At the moment, it wont let me O/C so we need to pull the kernel apart.. and put some new governors in it..
ok.. I will start the bidding..
kickstarter...
$US50 to any PayPal account for someone to supply me a kernel that I can flash and can O/C
O.. if you could add in "uniput.ko" as well.. then we would be cooking with gas..
and now I am sure others will want it..
so if we all chip in..
I am sure someone could rise to the challenge..
an universal remote control will work with my atv 1000? my flymouse keybord is dead,
Probably not what you want to hear, but my flymouse died after 2 months. Its either £15 or so on Ebay or do what I did and go to argos and buy a cheap logitech wireless mouse. Works a treat.
$US50 to any PayPal account for someone to supply me a kernel that I can flash and can O/C
O.. if you could add in "uniput.ko" as well.. then we would be cooking with gas..
1: Market -even with fix (as per permissions file fix) it still doesn't want to load from market any file. not FC, just a DL error..
Not sure if this is related to your problem, but make sure to remove this file: android.hardware.nfc.xml from "permissions" folder in: /system/etc
Also regarding your SD card issues, I have 1 box with a faulty SD slot. So it might be the same with yours. You can flash the ROM using a USB stick. Does that get you past the 80%?
Thank you gio for your continued hard work...really making my ATV worth every penny and then some. Quick question does this version allow location services to work. I have the 29 firmware but with the NFL gamepass it can't locate my settings so looking to try another version.
Cheers
Thank you gio for your continued hard work...really making my ATV worth every penny and then some. Quick question does this version allow location services to work. I have the 29 firmware but with the NFL gamepass it can't locate my settings so looking to try another version.
Cheers
Hi Hocus, I have installed the "NFL GamePass" app and I have had the same issue
(both on 20120606 GB and 20120730 ICS releases).
So at this moment, even with latest firmwares, you don't solve your problem
$US50 to any PayPal account for someone to supply me a kernel that I can flash and can O/C
O.. if you could add in "uniput.ko" as well.. then we would be cooking with gas..
and now I am sure others will want it..
so if we all chip in..
I am sure someone could rise to the challenge..
Quote:
Originally Posted by avirex
I'm in for $50
ok, I will keep a running telly..
DG - 50
AVIREX - 50
LETS GET THIS THING GOING..
Last edited by dgcruzing; September 27th, 2012 at 05:06 AM.
Not sure if this is related to your problem, but make sure to remove this file: android.hardware.nfc.xml from "permissions" folder in: /system/etc
Also regarding your SD card issues, I have 1 box with a faulty SD slot. So it might be the same with yours. You can flash the ROM using a USB stick. Does that get you past the 80%?
Avirex,
yes, tried that when i was on the 30 firmware..by changing that file to a .bak file and rebooting.. but still no go..
I then have gone back to the 529 firmware.. via the recovery method.. and wiped everything 3x just to make sure.. then loaded 529..
and its working like a dream again.
unfortunalty as said.. have had to leave it behind and do some travelling. .so will be back to it in a few weeks.. after the 8th of oct..
so will play with it again..
I might try the wiping method like 3-4 times before I load the .30 firmware back on.. and see if it makes a difference..
As to SDcard.. I just brought a new 64gig here in Singapore on the way through.. so will see how this goes..
and as you pointed out.. we have the USB method which is good to know too..
dgcruzing this is out of my league but I believe the kernel and source for all of that stuff is published on Amlogic openlinux site.
great..
also looking at it,s still the older branch they are using..2.6.39 and not they 3.1 versions..
understanding that whoever takes it on will have their hands full as there is a stack of drivers to pack..
I am in no position to give it a crack as not a hack and pack guy..
but I am hands up for beta testing..
Last edited by dgcruzing; September 27th, 2012 at 07:29 AM.
XBMC media center (Video, Music, Photo,... AllInOne),
Link download xbmc.apk
It work perfectly in ATV1000 with hardware acceleration HD, not full support fly mouse keyboard
Please try it
The Following User Says Thank You to ziczac For This Useful Post:
the hd streams works perfect, no lag? is working with the mouse?
i had before instaled the xbmc linux and the hd streams worked without problems only is full with bugs
try to install navix plugin and see if the streams arw not chopy
Last edited by everst; September 28th, 2012 at 08:23 AM.
Device(s): HTC One X
iPad,iPad2
Galaxy Tab 8.9
iTouch
Wii
Mac Book Pro
Nexus One
Carrier: Not Provided
Thanks: 34
Thanked 9 Times in 8 Posts
Quote:
Originally Posted by dgcruzing
I am going to need a new name..haha.. too many posts..
I wanna O/C this thing..
We need source for the kernel..
As I was saying above.. if we can get the 3 part flashing going.. then it means we can flash kernel separately..
i.e - flash u-boot upgrades..flash image upgrades and then flash Kernel..
Bloody Chinese need to release source so some bright bugger can work on it..
I am sure we could over clock the box's up to 1200-1400 as heat is not a problem on mine..
its got a fan and well ventilated.. so I would love to see how fast and stable the 800's are on o/c..
I am kinds spewing.. should have done a bit more research on them.. as the dual core are out already..
thinking of selling mine and upgrading already.. but might kill it instead with playing with it..as they are cheap enough..
At the moment, it wont let me O/C so we need to pull the kernel apart.. and put some new governors in it..
ok.. I will start the bidding..
kickstarter...
$US50 to any PayPal account for someone to supply me a kernel that I can flash and can O/C
O.. if you could add in "uniput.ko" as well.. then we would be cooking with gas..
and now I am sure others will want it..
so if we all chip in..
I am sure someone could rise to the challenge..
Very interesting, really you can O/C this box ? if you get all the source code you need?
Very interesting, really you can O/C this box ? if you get all the source code you need?
I can't see why not..
most chips are under clocked for health reasons..
manufacturers want them to run at a stable speed for the hardware matched to them..
if we are able to them control the governor's via the kernels..then in theory we should be able to O/C.
The M1-3000 is advertised with a ARM Contex A9, 800Mhz - 1000gHz clock speed..the stock kernel is limited it to 800 on mine.
thus I am missing out on that extra 200gHz-400ghz..
My 1000gHz transformer has been running for a year on 1480 with no drama's and some run them to 1700..
So I am betting we can a comfortable 1200- 1400 out of these box's if we get a kernel that opens these speeds up to use to play with..
As to heat..as we have a internal fan and mine seems well ventilated..minus the harddrive at this stage..as this will introduce heat into the area as well..
hy , first of all ,i'm new of this forum ,and in second time sorry for my english;in this last year that i bought a atv 1000 i appreciate a lot this forum...
i upgraded three times the device from 2.3 gb to ics4.0...
for me it's important to use skype on this m1 and when i used 2.3gb the video output of the webcam ,logitechc270, worked fine but not the audio.
upgraded to 4.0 ics the audio work fine but during the video call the person connected with me cannot see my video,so it seeems to having understood that this realease work fine with skype UPDATE 20120606 M1 2.3 it's that true...please make me know..
even it could depend by multiple variables :connection,cpu speed ,ram, and so on..
if somebody knows ...??!!
thanks a lot and greetings
Last edited by AGILULFO7; September 29th, 2012 at 03:48 AM.
I have the Diamond Multimedia AMP1000, which is a re-branded ATV1000.
It is upgraded to ICS 4.0.3.
I have connected a Western Digital 1TB MyBook as sda1, with lots of movies on it. That's great if I want to watch the movies on the AMP1000, but I want to share those files on my LAN.
With my WDTV Live Streaming Media Player, its attached drive is visible on the LAN. But my AMP1000 is not seen on the network.
So, is there a way, through a third-party Android app or through an option on the AMP1000 settings, to share its drive on the LAN?
hy , first of all ,i'm new of this forum ,and in second time sorry for my english;in this last year that i bought a atv 1000 i appreciate a lot this forum...
i upgraded three times the device from 2.3 gb to ics4.0...
for me it's important to use skype on this m1 and when i used 2.3gb the video output of the webcam ,logitechc270, worked fine but not the audio.
upgraded to 4.0 ics the audio work fine but during the video call the person connected with me cannot see my video,so it seeems to having understood that this realease work fine with skype UPDATE 20120606 M1 2.3 it's that true...please make me know..
even it could depend by multiple variables :connection,cpu speed ,ram, and so on..
if somebody knows ...??!!
thanks a lot and greetings
yes 0606 works ok with skype. only question is resolution of camera - the bigger resolution slower video.
XBMC media center (Video, Music, Photo,... AllInOne),
Link download xbmc.apk
It work perfectly in ATV1000 with hardware acceleration HD, not full support fly mouse keyboard
Please try it
I have the Diamond Multimedia AMP1000, which is a re-branded ATV1000.
It is upgraded to ICS 4.0.3.
I have connected a Western Digital 1TB MyBook as sda1, with lots of movies on it. That's great if I want to watch the movies on the AMP1000, but I want to share those files on my LAN.
With my WDTV Live Streaming Media Player, its attached drive is visible on the LAN. But my AMP1000 is not seen on the network.
So, is there a way, through a third-party Android app or through an option on the AMP1000 settings, to share its drive on the LAN?
If you look on Google Play market for samba you will find some samba server apps like this one, you might have to try a few to see which works.
I'm not sure these boxes would be fast enough for streaming media either so you might want to see about a DLNA server app instead which might makes things a little faster.
yes 0606 works ok with skype. only question is resolution of camera - the bigger resolution slower video.
thank'you very much for the answer , but when i reinstall 0606 skype video works but it find immediatly the upgrade for skype and after having done the upgrade skype webcam doesn't work no more,i though not to do the upgrade the skype but it didn't work audio for skype...so how can i set the resolution for webcam in skype...!!!???
sorry always for my english and thanks a lot!!
i'm not sure that skype do upgrade by itself?! try to diseable "automatic upgrade" option in goole play. i'm use to use skype on different devices and never got situation that upgrade is done by automatism.
resolution in skype is not possible to set by number, only with last item in settings "video quality" -> high - low. but i'm always use it on high, so i can't tell is there any big difference.
few months ago, and few pages on this topic back i posted question about camreras, and seems that little number of users use skype with box so i didn't get my answer - same as yours. and in the and, instead HQ logitech 270 i bought logitech 210 camera. just because of slow video and because everything was wery slow and laggy because high res camera.
i'm not sure that skype do upgrade by itself?! try to diseable "automatic upgrade" option in goole play. i'm use to use skype on different devices and never got situation that upgrade is done by automatism.
resolution in skype is not possible to set by number, only with last item in settings "video quality" -> high - low. but i'm always use it on high, so i can't tell is there any big difference.
few months ago, and few pages on this topic back i posted question about camreras, and seems that little number of users use skype with box so i didn't get my answer - same as yours. and in the and, instead HQ logitech 270 i bought logitech 210 camera. just because of slow video and because everything was wery slow and laggy because high res camera.
and you english is very good! ;-)
thank you very much...
it's not an absolute necessity i use skype on M1 , cause like you i use it on multiple devices, it's only a curiosity if it's low ram and so on...
i'll try your solution with low resolution camera...
thank's a lot...!!!
Last edited by AGILULFO7; October 2nd, 2012 at 07:41 AM.
Device(s): Geniatech ATV1000, HTC Wildfire, HP Touchpad (WebOS& ICS Alpha)
Carrier: Not Provided
Thanks: 11
Thanked 0 Times in 0 Posts
Lo there. All this talk of Skype. Picked up a cheap Logitech c110 in supermarket the other day. Only a few quid.
With ICS Skype starts but video has huge lags and audio does not seem to work properly.
Thought that as this was a low spec non-HD Webcam, and also Logitech like the C210, then I had a chance of it working. Set video Qual to "low" btw.
Is this likely to be a webcam compatibility issue or not? As it seems people above are having issues with compatible C210's in ICS.
210 works. first there was proble with camera drivers, and native camera app. that was solved with third-party app (quick snap) and after that all went ok. in sticky is little text about cameras. basicaly - it must be driverless. lag is constant because low memory of device. only solution is to free ram with some task killer and start up skype only.
@AGILULFO7, yes, that is problem - low memory, and skype itself gettin' bigger and bigger. and more and more complex app and slowly becoming somekind of multi-IM app. imho, loosing that first purpouse. but, luckely, there is few other apps which will very likely in future replace skype.
Device(s): HTC One X
iPad,iPad2
Galaxy Tab 8.9
iTouch
Wii
Mac Book Pro
Nexus One
Carrier: Not Provided
Thanks: 34
Thanked 9 Times in 8 Posts
Quote:
Originally Posted by jschall
I have the Diamond Multimedia AMP1000, which is a re-branded ATV1000.
It is upgraded to ICS 4.0.3.
I have connected a Western Digital 1TB MyBook as sda1, with lots of movies on it. That's great if I want to watch the movies on the AMP1000, but I want to share those files on my LAN.
With my WDTV Live Streaming Media Player, its attached drive is visible on the LAN. But my AMP1000 is not seen on the network.
So, is there a way, through a third-party Android app or through an option on the AMP1000 settings, to share its drive on the LAN?
210 works. first there was proble with camera drivers, and native camera app. that was solved with third-party app (quick snap) and after that all went ok. in sticky is little text about cameras. basicaly - it must be driverless. lag is constant because low memory of device. only solution is to free ram with some task killer and start up skype only.
@AGILULFO7, yes, that is problem - low memory, and skype itself gettin' bigger and bigger. and more and more complex app and slowly becoming somekind of multi-IM app. imho, loosing that first purpouse. but, luckely, there is few other apps which will very likely in future replace skype.
NP! i'll try to help if i know! ;-)
Hi Vikidroid.
Can you explain this comment about "quick snap"? Are you saying it includes some drivers to make the webcam work smoother? I havent tried this method, where do we get this quick snap app? For me the Skype video conf is not smooth at all (using latest GB firmware).
older version of GB OS, used to have broken camera app. only what was working was gallery. if you tryed to start camera, there was error message about app. so, i needed to find as smaller and lighter app that works. and from few different apps (camera zoom, 360camera, camerafx....) i found this one. i can't give you direct link to app, but there is link to google play. hope that admin alowes that.
after instalation, and after testing and tryng all of other free and/or payed apps, this one was smaller, simplyest and it works as it supposed. no more, no less. _after_ instalation of that app i managed to receive good, stabile (little bit laggy) pic in skype.
about smoothenes of video in skype, i already wrote, try in settings to set to low, and try with other camera with low resolution (0,3mpix will do the work).
If you look on Google Play market for samba you will find some samba server apps like this one, you might have to try a few to see which works.
Thanks, I installed the Samba Server on my AMP1000, and it works, but only for the SD card, not for the WD USB HDD. The Samba Server app can only share VFAT-formatted devices :-(
Thanks, I installed the Samba Server on my AMP1000, and it works, but only for the SD card, not for the WD USB HDD. The Samba Server app can only share VFAT-formatted devices :-(
-set options (at the bottom of the settings) - do not overwrite the file smb.conf
-with root to edit the file - /data/data/com.funkyfresh.samba/files/smb.conf - replaced at the end of file - /mnt/sdcard to /mnt
All partitions are mounted to /mnt will be seen. (Check the disks with the file systems ntfs, ext3)
Last edited by schit; October 5th, 2012 at 07:08 AM.
My AMP1000 is not rooted, so I can't edit that samba.conf file.
Are there any instructions on how to root the Geniatech ATV1000?
use esfile explorer or Solid explorer
on esfile explorer go into settings and allow for root view..
also show hidden files..
Then you can edit the files as you please..
as said.. All Geniatech comes rooted..
52Likes
XBMC with hardware acceleration on Android
AMP1000 (ATV1000) as a file server?
