I have a 2005 Jeep GC with U-connect, and it works fine. Might try un-pairing the phone, and re-pairing. Make sure you follow the instructions, which I will admit, aren't exactly the most clear.

 

Same problem but with incredible. Worked for day but then quit. Did new paring did not help.

 

I just purchased an HTC EVO Slide last week and then tried to connect to my 2010 Dodge Ram Uconnect. It would never hold a connection. It would connect for a few minutes and then disconnect. After speaking with Uconnect's Customer "NO SERVICE" department, they were absolutley no help and could not answer a single question. They just keep refering me back to the Dodge dealership, which knows nothing about their Uconnect. Turns out the phone is not compatible, so I sent the phone back.

This week I got the Samsung EPIC phone. The good news is that it pairs and connects with the Uconnect with no problem. Bad news is I cannot upload my phone book to the Uconnect!

I'm about ready to go back to my Blackberry Tour and say the hell with it, it just works. The real problem here is with the $300.00 piece of $h!t Uconnect that you can't get any updates or support on.

 

The really wierd thing is that the phone book will upload a few contacts but will not recognize the persons name. I will ask me if I want to "accept" the contact, then I have to speak the persons name and confirm it in order for the contact to save in the phone book. I have 120 contact and I would have to go through that entire process for each contact. There is probably a error in the fields in the databases between the two units.

Even beside the connection issues, the Uconnect is still a piece of $h!t with it's terrible voice recognition and picking up "wind/background noise" in the mic so bad that people on the other end have a hard time hearing. I've rented a ton of other make vehicles and their hands free bluetooth systems were awesome. I'm just really pissed over the No Customer Service...

 

According to htc/ford and chrysler, the evo is not yet compatible with ford sync or chrysler's u-connect. I have both and i'm waiting for the upgrade htc says is coming soon. You should not have to mess around with deleting contacts and linking and all that stuff. The system should connect reliably and download your phone book and not disconnect the bluetooth.

I will rejoice when the upgrade finally arrives.

 

Hello,
To anyone using the HTC EVO 4G, Shift and others (these were the only 2 that I have been able to test that were having problems). I have tested a new SW for HTC and the Uconnect system. HTC was send the phone book download in an unsupported way and causing the hands free kit to reset. (this was true with many other kits other that Chrysler, ex: Ford, GM,BMW, Toyota, Blue tooth ear buds etc). The SW version was for Android 2.3, it tested good for the phone section however the streaming audio still was sounding choppy. This is because HTC ( and others) want to try to give you better sound and are using a bit pool of 35. The various kits support bit pools of 18 -25. HTC has recently (the last couple weeks) this update as an OTA update. Now I don't know about the other companies but Chrysler has just released a SW update that needs to be performed at the dealership service dept. The TSB # is 08-036-11. The description is to cure Apple products "error occurred"in cabled iPod mode and also their choppy streaming audio when the device back lighting is on. I would suggest that if you have a Jeep, Chrysler or Dodge vehicle and don't have an Apple phone, tell them that you have an iPod touch or they will tell you that the TSB does not apply to you.
I have tested this SW update and it works for the choppy audio on the Samsung Captivate, HTC EVO 4G & Shift, Motorola Droids as well as several other phones.
If you have the Samsung Transform, Epic, captivate (possibly others) and have updated their Android SW to the 2.2, you will experience that the Phone book used to download but now it doesn't. If the PB was already downloaded before the Android update, it may still be there, the problem may be that if you have deleted or added any contacts that they editing won't be changed on the PB that is stored in the HF kit.
Each time you turn the key off & exit the vehicle, when you come back and turn the key on the PB is downloaded and compared to the saved PB to look for any changes that have been made while you were away from the vehicle.

NOW PLEASE NOTE: If you have a Chrysler vehicle and you took it in for the SW Update PLEASE DO THIS (to keep you from being possibly aggravated).

If you do have an Apple product, plug it into the USB connector using the iPod cable, does it work properly? Unplug it, turn the key off, wait a couple minutes and turn the key back on & plug it back in. Does the "error occurred" message come on?
Also now unplug it and pair it up, play the Streaming audio, press the "wake" button so that the back lighting comes on (so you can see the "now playing", album, artist, etc) does the streaming audio now play choppy, ("no", then the update was done properly, "yes" then go back inside and tell them it either wasn't done or it was done improperly)
For those without Apple products:
If your phone was dropping the Bluetooth connection, had choppy audio etc. Try to duplicate the issue you were having and just as above, if the issue is there still go back inside and ask if they are sure that the update was performed properly.
I mentioned this last note because the TSB was released on 6-29-2011, I posted it on a Jeep forum first. There have been a few different people in different states that have taken the vehicle in for the TSB and some were told that it does nor exist however it is on the Chrysler Dealer Connect web site where their techs go for diagnostic steps, schematics, DTC's etc, so they all have it. Also there are some who left their vehicles for it to be done only to drive away with their Apple device working fine but only to be disappointed the next time they use it in the vehicle. The key thing that told me that it was either not being done or done incorrectly was the streaming audio.
I apologize for being so long winded here but I wanted to answer any questions that I thought you may ask while reading this. (and No, I don't think I can read your mind, HAHA JK)

 

May I ask which BB that you are using and what network is it on.
As for the Epic, if it has Android 2.2 on it, this update messed it up. I have notified Samsung of this and I was emailed last week that they are working on a SW update to cure this. Hopefully they will let me test it for them before the offer it OTA. This is the same thing for the Samsung Transform also.
It was an issue that HTC was having also with the PB download that was causing the BT kits to reset. HTC came out with their 2.3.3 update that cured it.

 

I just bought a 2012 Durango w/ uconnect. Have EVO 3D (Sprint) The Bluetooth paired fine and phone works fine through Radio. Playing media files, different story. I can play songs, but the player will not pause, stop, or even force close. Every time I force close it the app reloads withing a few seconds and continues playing. I also was able to stream audio from netflix through BT, but music was playing over it. Anyone got any suggestions? I did find how to disable playing media on BT settings. I will use AUX jack for media until I can get this worked out. Thanks

 

Hello, I will test this for you on Monday (11-07-2011) and get back to you. If there an issue, I can let my contact at HTC know about it.

 

[FONT=&quot]Now what I have seen is:[/FONT]
[FONT=&quot]1) [/FONT][FONT=&quot]The media player itself does seem to pause and I can play a different audio media (such as Pandora or Slacker radio)[/FONT]
[FONT=&quot]2) [/FONT][FONT=&quot]If I am playing (ex Pandora and go to Netflix and start playing a item there, Pandora does not end and let Netflix play. They seem to ride over each other (you can hear both).[/FONT]
[FONT=&quot]3) [/FONT][FONT=&quot]If I am playing Pandora and switch to Slacker radio or Sprint radio, this seems to work ok.[/FONT]
[FONT=&quot]4) [/FONT][FONT=&quot]It seems like issues happen when Netflix is involved (at least at this point).[/FONT]
[FONT=&quot] [/FONT]


[FONT=&quot] [/FONT]

 

Aftermore careful testing on this issue, I found that all the audio apps will at times interfere with each other.This issue has been reported to HTC, they have been able to reproduce it as well and they are looking further into it. I will let you know more as I hear from them.

 

I have an HTC EVO 4G and it connects to the UConnect system in my 2011 Dodge Durango just fine for phone purposes, but when I try to use the Bluetooth Audio feature... the music playback is "sketchy". It sounds like a CD that is skipping... It will play a few seconds of a song quickly, then stop, and repeat this process over and over... Is there anything that I can do to get this to stop? All advice is welcome...

 

I too have this issue.
2011 ram 1500, no touch screen radio.

I will post the factory tech issue after this post.
I guess I have to make a post first before images can be posted..

 

NUMBER: 08-015-11
GROUP: Electrical
DATE: April 06, 2011
THIS SERVICE BULLETIN IS ALSO BEING RELEASED AS RAPID RESPONSE TRANSMITTAL (RRT) 11-034. ALL APPLICABLE SOLD AND UN-SOLD RRT VIN's HAVE BEEN LOADED. TO VERIFY THAT THIS RRT SERVICE ACTION IS APPLICABLE TO THE VEHICLE, USE VIP OR PERFORM A VIN SEARCH IN TECHCONNECT. ALL REPAIRS ARE REIMBURSABLE WITHIN THE PROVISIONS OF WARRANTY.
SUBJECT:
Loss Of Communications With HFM

OVERVIEW:
This Bulletin involves performing a USB service flash of the Hands Free Module (HFM).

MODELS:
2011 (LC) Challenger2011 (MK) Compass / Patriot2011 (PM) Caliber2011 (WK) Grand Cherokee2011 (W2) Grand Cherokee2011 (WD) Durango2011 (KK) Liberty2011 (K1) Cherokee2011 (KA) Nitro2011 (JS) Avenger/2002011 (DS) 1500 Pickup2011 (DJ) 2500 Pickup2011 (D2) 3500 Pickup2011 (DD) 3500 Cab Chassis2011 (DP) 4500/5500 Cab Chassis2011 (DX) 1500 Pickup (Mexico)2011 (JK) Wrangler2011 (RT) Grand Caravan / Town & Country
NOTE :This bulletin applies to PM/MK vehicles built from October 26, 2010 (MDH 1026XX) to November 22, 2010 (MDH 1122XX) equipped with UCONNECT VOICE COMMAND W/BLUETOOTH (sales code RSP, RSQ for international) and without MEDIA CENTER 730N CD/DVD/MP3/HDD/NAV (sales code RER) or MEDIA CENTER 735N CD/DVD/HDD/NAV (sales code REW) or MEDIA CENTER 731N CD/DVD/HDD/NAV (sales code REP).

NOTE :This bulletin applies to WK/W2/WD/KK/K/KA vehicles built from November 8, 2010 (MDH 1108XX) to November 22, 2010 (MDH 1122XX), equipped with UCONNECT VOICE COMMAND W/BLUETOOTH (sales code RSP, RSQ for international) and without MEDIA CENTER 730N CD/DVD/MP3/HDD/NAV (sales code RER) or MEDIA CENTER 735N CD/DVD/HDD/NAV (sales code REW) or MEDIA CENTER 731N CD/DVD/HDD/NAV (sales code REP).

NOTE :This bulletin applies to DS/DJ/D2/DD/DP/DX vehicles built from October 26, 2010 (MDH 1026XX) to November 30, 2010 (MDH 1130XX), equipped with UCONNECT VOICE COMMAND W/BLUETOOTH (sales code RSP, RSQ for international) and without MEDIA CENTER 730N CD/DVD/MP3/HDD/NAV (sales code RER) or MEDIA CENTER 735N CD/DVD/HDD/NAV (sales code REW) or MEDIA CENTER 731N CD/DVD/HDD/NAV (sales code REP).

NOTE :This bulletin applies to JS vehicles built from November 4, 2010 (MDH 1104XX) to November 19, 2010 (MDH 1119XX), equipped with UCONNECT VOICE COMMAND WIBLUETOOTH (sales code RSP, RSQ for international) and without MEDIA CENTER 730N CD/DVD/MP3/HDD/NAV (sales code RER) or MEDIA CENTER 735N CD/DVD/HDD/NAV (sales code REW) or MEDIA CENTER 731N CD/DVD/HDD/NAV (sales code REP).

NOTE :This bulletin applies to JK vehicles built from October 26, 2010 (MDH 1026XX) to November 30, 2010 (MDH 1130XX), equipped with UCONNECT VOICE COMMAND W/BLUETOOTH (sales code RSP, RSQ for international) and without MEDIA CENTER 730N CD/DVD/MP3/HDD/NAV (sales code RER) or MEDIA CENTER 735N CD/DVD/HDD/NAV (sales code REW) or MEDIA CENTER 731N CD/DVD/HDD/NAV (sales code REP).

NOTE :This bulletin applies to RT vehicles built from October 26, 2010 (MDH 1026XX) to November 19, 2010 (MDH 1119XX), equipped with UCONNECT VOICE COMMAND WIBLUETOOTH (sales code RSP, RSQ for international) and without MEDIA CENTER 730N CD/DVD/MP3/HDD/NAV (sales code RER) or MEDIA CENTER 735N CD/DVD/HDD/NAV (sales code REW) or MEDIA CENTER 731N CD/DVD/HDD/NAV (sales code REP).

NOTE : This bulletin applies to LC vehicles built prior to November 29, 2010 (MDH 1129XX), equipped with UCONNECT VOICE COMMAND W/BLUETOOTH (sales code RSP, RSQ for international) and without MEDIA CENTER 730N CD/DVD/MP3/HDD/NAV (sales code RER) or MEDIA CENTER 735N CD/DVD/HDD/NAV (sales code REW) or MEDIA CENTER 731N CD/DVD/HDD/NAV (sales code REP).

SYMPTOM/CONDITION:
The customer may experience the following:
^Loss of function of the HFM
^Loss of Communications with the HFM during a wiTECH diagnostics session
^Loss of Communications faults may set against the HFM by other modules
^Upon resetting the HFM a "Loss of Comm with Radio" DTC may be stored

DIAGNOSIS:
1.Place the ignition in the RUN position and wait at least 15 seconds.
2.Remove the main IOD Fuse (i.e. M13).
3.Wait at least 10 Seconds.
4.Reinsert IOD Fuse and verify proper seating.
5.Press the radio's phone button.
6.Quickly turn the radio volume control knob to above 3/4 of maximum volume and leave it there.
7.Did the vehicle audio system play any of the following verification prompts: "UConnect Ready... beep", "Ready ... beep", or just an audible "beep"?
a.YES >>> Proceed to step Step # 9.
b.NO >>> Proceed to step Step # 8.
8.Have you attempted to 'Verify the HFM is powered up' at least twice previously without receiving an audible HFM verification prompt?
a.YES >>> This service bulletin does not apply. Further diagnostics may be required.
b.NO >>> Return to step Step # 5.
9.Press the radios's phone button to end the phone session. HFM power up verification is complete.
10.Using wiTECH, determine the HFM part number. The HFM part number can be found under Module Information for the HFM.
11.Is the HFM Part number one of the following: 05064634AH, 05064635AH, 05064735AH, 05064870AH, 05064870AH, 05064730AH, 05064730AH, 05064871AH or higher?
a.Yes >>> Perform the Repair Procedure.
b.No >>> This service bulletin does not apply. Further diagnostics may be required. If a customer's VIN is listed in VIP or your RRT VIN list, perform the repair. For all other customers that describe the symptom/condition, perform the Repair Procedure.


PARTS REQUIRED:
NOTE :Only one UConnect Hands Free Module USB Flash Drive Preparation CD is required and this disk may be used to prepare multiple USB Flash Drives.

REPAIR PROCEDURE:

HFM USB Connector Location Table
Prepare USB Memory Stick
1.Insert the dealer supplied USB flash drive into an available USB port on the computer being used to prepare the USB flash drive for HFM reflash.
2.Insert CD PN # 68139848AA (UConnect Hands Free Module USB Flash Drive Preparation CD) into the computer's CD drive. (If the CD does not automatically start, open your file browser, go to the CD drive, and double click on the autorun file.)
3.Follow the on screen prompts to prepare the USB flash drive to be used for the HFM reflash.

Perform Software Reflash
NOTE :Install a battery charger to ensure battery voltage does not drop below 13.2 volts. Do not allow the charging voltage to climb above 13.5 volts during the flash process.

CAUTION amage to the HFM may occur! Do not interrupt vehicle power, cycle ignition, or remove the USB memory stick while performing software reflash.

1.Locate the HFM USB using the HFM USB Connector Location Table (This is NOT the same as the USB port located on the radio).
2.Access the HFM USB Connector (Go to Special Instruction for KA/KK only).
3.Insert the HFM software update USB Memory Stick into the USB Connector.
4.Sit in the passenger seat and close all doors and windows.
5.Press and release the radio's u-Connect Phone button and, following the HFM verification prompt, say "Set-up, Software Update". The system will respond with an audio prompt stating: "Starting Software Update, Please Wait".
6.The audio prompt will be followed by periodic beeps for approximately 2 minutes. After the periodic beeps end the radio will exit re-flash mode and return to the last radio mode.
NOTE o not remove the USB memory stick at this point.

7.Wait one additional minute for the HFM to complete the update and reset.
NOTE :In the event of a reflash failure the system will respond with an audio prompt indicating "Digital Signature not recognized" or USB Mass Storage device not compatible". If this should occur, re-prepare the USB Flash Drive using a different USB port on the computer. If this does not resolve the issue use another brand of flash drive.

Verify Software Reflash
1.Press the radio's phone button.
2.Quickly turn the radio volume control knob to above 3/4 of maximum volume and leave it there.
3.Did the vehicle audio system play any of the following verification prompts: "UConnect Ready... beep", "Ready ... beep", or just an audible "beep"?
a.YES >>> Proceed to Step # 4.
b.NO >>>> Proceed to Step # 7.
4.Press the radio's phone button to end the session.
5.Using wiTECH, determine the HFM part number. The HFM part number can be found under Module Information for the HFM.
6.Is the HFM Part number one of the following: 68142503AA, 68142505AA, 68142507AA, 68142510AA?
a.Yes >>> Proceed to Step # 8.
b.No >>> Proceed to Step # 7.
7.Have you attempted the Flash Procedure at least twice previously?
a.YES >>> This service bulletin does not apply. Further diagnostics may be required.
b.NO >>>> Reattempt the 'Perform Software Reflash' procedure.
8.Remove and properly store the USB Memory Stick.
9.Using WiTECH clear any faults which may have been set during the reflash procedure.
10.KA / KK vehicles only, return to the Special Instructions

Special Instructions (KA / KK Only)
The 2011 KA (Nitro) and KK (Liberty) are not equipped with the USB port. They have the capability of being upgraded by using the MOPAR PN # 82212160 (USB Harness) for the reflash process.
The HFM Module on the KA / KK is located on the right rear side (passenger's side on left hand drive vehicles also), and behind the audio system's subwoofer enclosure.
1.Access the HFM Module by following steps 1 through 4 in DealerConnect / TechCONNECT > Group 08 - Electrical > 81 - Navigation/Telecommunications > MODULE, Hands Free (HFM) > Removal - REMOVAL.
2.Do NOT disconnect the electrical connectors from the HFM.


3.Connect the USB harness (PN # 82212160) as shown in (Fig. 1).
4.Reconnect the battery.
5.Return to the Perform Software Reflash Procedure Step # 3.
6.Disconnect and isolate the battery negative cable.
7.Reinstall HFM Module by following steps 2 through 5 in DealerConnect / TechCONNECT > Group 08 - Electrical > 81 - Navigation/Telecommunications > MODULE, Hands Free (HFM) > Installation - INSTALLATION.
POLICY:
Reimbursable within the provisions of the warranty.


TIME ALLOWANCE:

FAILURE CODE:
Disclaimer :This bulletin is supplied as technical information only and is not an authorization for repair.

 

I don't really know what all of this means... Do I need to take my car to a dealership? And if so, does it cost? Have you tried to perform this on your car? Do you know if it will even work? I appreciate the help, but I am still lost...

 

My wife and I recently upgraded our phones
I have Samsung Galaxy II S
she has Samsung Infuse

Our dodge Vehicles both 2010 models have had problems loading the contacts like our previous BB's did automatically.

I have just a simple cd /Sat radio in my challinger while she has the touch screen version (no nav) in her Ram truck.

On the RAM with the infuse. I paired the infuse with no problem but when she presses the phone on the uconnect it locks up as it acts if it going to download but it doesnt.

The fix: get in and start the vehicle... dont touch the uconnect yet.
look on your phone and wait until the bluetooth shows connection

THEN on your phone
Press MENU
Press SETTINGS
Press WIRELESS AND NETWORK
press BLUETOOTH SETTINGS
press VISIBLE

After a few seconds you contacts will download to the uconnect and u can use the system normally

You must do this each time you get in your vehicle for the INFUSE if I find a way to make it permanent I will let you know with a repost.

The galaxy fix you only have to do one time

On the GALAXY

Get in vehicle
ON YOUR PHONE Pull down the NOTIFICATION BAR from the top

start the vehicle
you should see a item saying uconnect request contacts (or something like that)
ON YOUR PHONE press that notification
a window will come up and say Allow Download? and check the box that says Don't ask again (or make permanent) then click OK

you can now use your phonebook from your galaxy with your uconnect

IF I figure out how to make the infuse fix permanent I will let you know.

 

I have my 2011 Durango in the shop at this moment for the same issue with my Sprint Samsung Epic 4G touch. Same thing with my Galaxy Tab, Evo 4G and Wife's Epic 4G touch with different radios...they couldn't do anything because my radio is on the latest software version. I consider myself a poweruser of these devices and will figure this one out. Will share my results and experience.

 

i have a 2011 nitro. and when i try playing pandora through my uconnect the songs are repeatedly skipping which is annoyign and makes it impossible to listen becasue it sounds like its fast forwarding. any ideass??

 

also my phone is a samsung galxay s2

 

Here you go. This the Uconnect SW update for the 2011 Chrysler, Dodge & Jeep vehicles that have the High Speed CAN BUS network. (wranglers, rams, durangos, liberty, nitro, caravan, grand Cherokee).

Here's the Uconnect update instructions:
Download it to a thumb drive that has no other files on it. If you have files on it, please delete them and format the drive (to FAT32) just to make sure that it is completely clean.
Turn the radio on, Place the thumb drive in the center console USB connector (on vehicles with the dealer installed unit, it should be in the glove box), press and hold the Uconnect button for about 12 - 15 seconds, you should here "update started". This process should take about 15 - 20 minutes, there will be some beeps during the process. Please listen during the update for any error message that may be said by Uconnect. When the update is completed, the radio screen will go back to a radio display. Now plug in your iPhone or iPod and let it be read by Uconnect, does it start playing after being read? COOL


Hope this helps you guys (and ladies). This will take care of a lot of streaming audio issues with phones other than IPhone's, the error occurred when trying to use an iPod or IPhone with the docking cable.

uconnect.upd

 

Thanks! This download/update worked perfectly!! And best of all, my phone (EVO 4G - Sprint) works seamlessly, and effortlessly with my car... the way that it should! You're the best!