1. 2015 is going to be a great year for Android! Why wait??
    Samsung Galaxy Note 5 | Samsung Galaxy S6 | HTC One M9
  2. New Forum Created: Samsung Gear VR!

1st attempt to root VRUAMDK via Odin failed


  1. beowulf7

    beowulf7 Well-Known Member

    I tried to root my VZW SGS4 that fortunately came with the older VRUAMDK firmware. I followed these instructions. However when I got into ODIN mode and then opened up Odin 3.07 and connected the USB cable on my Windows 7-64 computer and PDA opened, SCH-I545_MD2_423399_Kernel.tar.md5, it failed. I tried again but this is as far as I got:
    <ID:0/004> Added!!
    <OSM> Enter CS for MD5..
    <OSM> Check MD5.. Do not unplug the cable..
    <OSM> Please wait..
    <OSM> SCH-I545_MD2_423399_Kernel.tar.md5 is valid.
    <OSM> Checking MD5 finished Sucessfully..
    <OSM> Leave CS..
    <ID:0/004> Odin v.3 engine (ID:4)..
    <ID:0/004> File analysis..
    <ID:0/004> SetupConnection..

    I was stuck in that ODIN mode, none of the buttons would respond. So I popped out the battery and turned my phone back on normally and everything appears to be OK (and obviously still running VRUAMDK). Did anyone's initial attempt fail? I'm a little afraid to try again. Or maybe I'll update my firmware to VRUAME7 since its root procedure is much simpler. (Yes, I know it's not a full root since I can't install other ROMs ... yet). TIA for any advice you could give.

    Advertisement
    :
  2. Covert_Death

    Covert_Death Well-Known Member

    you gotta wait like 5 minutes to let it complete try again and just let it do its thing... also do a fresh download of all the files, some of them may have been corrupt
  3. Podivin

    Podivin VIP Member VIP Member

    This is the method I used for mine.
    http://forum.xda-developers.com/showthread.php?t=2301720

    As with any attempt at rooting (or doing anything even slightly 'dangerous' with your phone) read everything fully and make sure you truly understand what to do BEFORE you start the process.
  4. beowulf7

    beowulf7 Well-Known Member

    Thanks for the replies. Yes, I realize the potential of bricking the phone, which I guess could happen if someone strayed even just a hair from the exact instructions. I'll re-attempt using the 2nd method. If that fails, then I'll do the OTA update to ME7 and use the easier method, which I understand would lock my ability to change ROMs, but would at least still give me root.
  5. timelord65

    timelord65 Well-Known Member

  6. beowulf7

    beowulf7 Well-Known Member

    Thanks, those are the instructions I tried to follow (as noted in my original post). But after I got in Odin mode, the COM port (which was #4 for me) did recognize my phone. But when I tried to flash the old (pre-release) firmware, it gave a note saying fail. Then when I exited Odin 3 and relaunched it in Windows, it wouldn't recognize my phone.

    My phone was in the Download mode and it was unresponsive to any buttons. So I unplugged its USB cable and pulled out the battery. I put it back together and the phone rebooted just fine with the stock MDK firmware.

    In the video, it shows the guy enabling USB debugging mode after flashing to the pre-release firmware (around 3:40 into the video). Should I have done it before connecting the USB cable the first time? Maybe he left that out, which caused my pre-release firmware attempt to fail. :confused:
  7. beowulf7

    beowulf7 Well-Known Member

    My 2nd attempt at rooting my phone worked! :cool: The only thing I did differently than my 1st attempt was to use the micro USB cable I have plugged in the back of the computer vs. the front.

    I followed these instructions step-by-step.
Loading...

Share This Page